33dBm GSM900/WCDMA2100 2g 3g 2W Band Selective Repeaters

Short Description:

Introduction Mainfeature Application&scenarios Specification Parts/Warranty GSM900/WCDMA2100 2W Band Selective Repeaters Kingtone RepeatersKingtone system is designed to solve problems of weak mobile signal, which is much cheaper than adding a new Base Station (BTS). Main operation of RF Repeaters system is to receive low‐power signal from BTS via radio frequency transmission and then transmit the amplified signal to the areas where network coverage is inadequate. An...

Send email to us Download as PDF

Product Detail

Product Tags

Introduction
Mainfeature
Application&scenarios
Specification
Parts/Warranty

GSM900/WCDMA2100 2W Band Selective Repeaters

Kingtone Repeaters
Kingtone system is designed to solve problems of weak mobile signal, which is much cheaper than adding a new Base Station (BTS). Main operation of RF Repeaters system is to receive low‐power signal from BTS via radio frequency transmission and then transmit the amplified signal to the areas where network coverage is inadequate. And the mobile signal is also amplified and transmitted to the BTS via the opposite direction.

Telephone repeater
This is used to increase the range of telephone signals in a telephone line. They are most frequently used in trunklines that carry long distance calls. In an analog telephone line consisting of a pair of wires, it consists of an amplifier circuit made of transistors which use power from a DC current source to increase the power of the alternating current audio signal on the line. Since the telephone is a duplex (bidirectional) communication system, the wire pair carries two audio signals, one going in each direction. So telephone repeaters have to be bilateral, amplifying the signal in both directions without causing feedback, which complicates their design considerably. Telephone repeaters were the first type of repeater and were some of the first applications of amplification. The development of telephone repeaters between 1900 and 1915 made long distance phone service possible. However most telecommunications cables are now fiber optic cables which use optical repeaters (below).

Cellular repeater
This is a radio repeater for boosting cell phone reception in a limited area. The device functions like a small cellular base station, with a directional antenna to receive the signal from the nearest cell tower, an amplifier, and a local antenna to rebroadcast the signal to nearby cell phones. It is often used in downtown office buildings.

Mainfeature: Main Features
◇ High linearity PA; High system gain
◇ Intelligent ALC technology
◇ Full duplex and high isolation
◇ Sharp filter curve
◇ Automatic Operation convenient operation
◇ Modular design ease to maintain
◇ Remote control/monitor/alarm via RF MODEM or Ethernet
◇ IP65 chassis design for both indoor and outdoor application

Application&scenarios

Applications
    To expand signal coverage of fill signal blind area where signal is weak
or unavailable.
   Outdoor: Airports, Tourism Regions, Golf Courses, Tunnels, Factories, Mining Districts, Villages etc.
   Indoor: Hotels, Exhibition Centers, Basements, Shopping
Malls, Offices, Packing Lots etc.
It is mainly applicable to such case:
    The repeater can find an installation place which can receive pure BTS signal at strong enough level as the Rx Level in repeater site should be more than ‐70dBm;

And can meet the requirement of antenna isolation to avoid self‐oscillation.

Specification

Technical Specifications

Items				Testing Condition	Specification
					Uplink	Downlink
Working Frequency(MHz)				Nominal Frequency	890 – 915MHz	935 – 960MHz
					1920 – 1980MHz	2110 – 2170MHz
Gain(dB)				Nominal Output Power-5dB	85±3
Output Power (dBm)				GSM modulating signal	33	33
ALC (dBm)				Input Signal add 20dB	△Po≤±1
Noise Figure (dB)				Working in-band（Max. Gain）	≤5
Ripple in-band (dB)				Nominal Output Power -5dB	≤3
Frequency Tolerance (ppm)				Nominal Output Power	≤0.05
Time Delay (us)				Working in-band	≤5
GSM		Peak Phase Error(°)		Working in-band	≤20
		RMS Phase Error (°)		Working in-band	≤5
WCDMA		EVM(%)		Working in-band	≤12.5
		PCDE (dB)		Working in-band	≤35
Gain Adjustment Step (dB)				Nominal Output Power -5dB	1dB
Gain Adjustment Range(dB)				Nominal Output Power -5dB	≥30
Gain Adjustable Linear(dB)			10dB	Nominal Output Power -5dB	±1.0
			20dB	Nominal Output Power -5dB	±1.0
			30dB	Nominal Output Power -5dB	±1.5
GSM	Inter-modulation Attenuation (dBc)			Working in-band	≤-45
WCDMA	±5.0			Working in-band	≤-45
	±10.0			Working in-band	≤-50
Spurious Emission(dBm)			9kHz-1GHz	BW:30KHz	≤-36	≤-36
			1GHz-12.75GHz	BW:30KHz	≤-30	≤-30
VSWR				BS/MS Port	1.5
I/O Port				N-Female
Impedance				50ohm
Operating Temperature				-25°C ~+55°C
Relative Humidity				Max. 95%
MTBF				Min. 100000 hours
Power Supply				DC-48V/AC220V(50Hz)/AC110V(60Hz)( ±15%)
Remote Monitoring Function				Real-time alarm for Door Status, Temperature, Power Supply, VSWR, Output Power
Remote Control Module				RS232 or RJ45 + Wireless Modem + Chargeable Li-ion Battery

Parts/Warranty

1 year warranty for equipment ,6month for accessories .

■ contat supplier ■ Solution&Application

*Model : KT-G/D/WRP-B25/75/60-P40-B
*Product Category : 43dBm GSM900&DCS1800&WCDMA2100 20W triple band cell phone signal Repeaters
*Model : KT-TRP-B15-P45-B
*Product Category : 30W Tetra800MHz Band Selective Repeaters
*Model : KT-VHF UHF
*Product Category : VHF uhf walkie talkie repeater Amplifier
*Model : KT-8102B-C
*Product Category : 17-25dBm indoor CDMA 850 cell phone signal booster repeater